- Qt 6.11
- Qt Serial Bus
- Qt SerialBus Examples
- CAN Bus Manager
- Qt 6.11.0 Reference Documentation

# CAN Bus Manager

The example sends and receives CAN bus frames.

The example sends and receives CAN bus frames. Incoming frames are ordered according to their type. A connect dialog is provided to adjust the CAN Bus connection parameters.

Key Qt Serial Bus classes used in this example:

- QCanBusDevice
- QCanBusFrame

#### Creating a QCanBusDevice

An instance of QCanBusDevice is required to perform any CAN communication.

The `ConnectDialog` allows to specify all the required parameters. After that the device is created using the provided plugin and interface names:

         QString errorString;
         m_canDevice.reset(QCanBus::instance()->createDevice(p.pluginName, p.deviceInterfaceName,
                                                             &errorString));
         connect(m_canDevice.get(), &QCanBusDevice::errorOccurred,
                 this, &MainWindow::processErrors);
         connect(m_canDevice.get(), &QCanBusDevice::framesReceived,
                 this, &MainWindow::processReceivedFrames);
         connect(m_canDevice.get(), &QCanBusDevice::framesWritten,
                 this, &MainWindow::processFramesWritten);

The established connections allow to process incoming frames, control the sent frames and handle errors.

When the device is created, use QCanBusDevice::connectDevice() to start the communication.

#### Processing Incoming Frames

QCanBusDevice emits a framesReceived() signal when new frames are available. The readFrame() method can be used to read a single QCanBusFrame while there are available frames. Once the frame is received, individual parameters such as frameId, timeStamp, or payload can be extracted from it:

         while (m_canDevice->framesAvailable()) {
             m_numberFramesReceived++;
             const QCanBusFrame frame = m_canDevice->readFrame();

             QString data;
             if (frame.frameType() == QCanBusFrame::ErrorFrame)
                 data = m_canDevice->interpretErrorFrame(frame);
             else
                 data = QString::fromLatin1(frame.payload().toHex(' ').toUpper());

             const QString time = QString::fromLatin1("%1.%2  ")
                     .arg(frame.timeStamp().seconds(), 10, 10, ' '_L1)
                     .arg(frame.timeStamp().microSeconds() / 100, 4, 10, '0'_L1);

             const QString flags = frameFlags(frame);

             const QString id = QString::number(frame.frameId(), 16).toUpper();
             const QString dlc = QString::number(frame.payload().size());

             m_model->appendFrame(QStringList({QString::number(m_numberFramesReceived),
                                               time, flags, id, dlc, data}));
         }

#### Sending Frames

To send custom data over the CAN bus, the user needs to provide at least a frameId and a payload. Optionally other QCanBusFrame parameters can be configured:

         const uint frameId = m_ui->frameIdEdit->text().toUInt(nullptr, 16);
         QString data = m_ui->payloadEdit->text();
         m_ui->payloadEdit->setText(formatHexData(data));
         const QByteArray payload = QByteArray::fromHex(data.remove(u' ').toLatin1());

         QCanBusFrame frame = QCanBusFrame(frameId, payload);
         frame.setExtendedFrameFormat(m_ui->extendedFormatBox->isChecked());
         frame.setFlexibleDataRateFormat(m_ui->flexibleDataRateBox->isChecked());
         frame.setBitrateSwitch(m_ui->bitrateSwitchBox->isChecked());

         if (m_ui->errorFrame->isChecked())
             frame.setFrameType(QCanBusFrame::ErrorFrame);
         else if (m_ui->remoteFrame->isChecked())
             frame.setFrameType(QCanBusFrame::RemoteRequestFrame);

Once the frame is prepared, the QCanBusDevice::writeFrame() method can be used to send it:

         m_canDevice->writeFrame(frame);

#### Running the Example

To run the example from Qt Creator, open the Welcome mode and select the example from Examples. For more information, see Qt Creator: Tutorial: Build and run.

Example project @ code.qt.io